Radiator Recycling Machine

Radiator Recycling Machine Introduction

The radiator recycling machine is designed to process scrap aluminum copper radiators normally used in air conditioning units. Cut the clean radiator neatly into 30-40cm wide, and then put into the material inlet, within seconds copper pipes and aluminum fin will be discharged separately. Copper pipe will keep complete, while aluminum fin will be a little broken for one-row radiator and keep complete for two-row radiator. The machine proves itself to be the best choice for scrap radiator recycling.

Features of Radiator Separating Machine

A. Automatic operating, high capacity
B. During the separating process, few losses for the copper and alu foil.
C. Low investment, high profit, eco-friendly
D. Easy operation, high efficiency, and labor-saving
E. Suitable to the stock size of air conditioner radiator: 25mm/25.4mm/21mm/19mm (pipe center distance). We could also customize the size as per your request.
F. Our machine has the guard bar to protect hands when operating.
G. The crushing strength can be adjusted, so as to get more complete alu foil.

Application of Radiator Recycling Machine

This machine is used for recycling scrap air conditioner radiators, its main function is to separate the copper pipe and aluminum foil. Separating rate can be up to 99.9%.
1. The machine is specially used for processing aluminum-copper radiators.
2. The machine is suitable for separating one-row and two-row radiators. For radiators of more than 2 layers, please use a band saw to cut them into one layer or two layers.
3. Center distance of two copper pipes in radiators shall be 19mm or 21mm or 25mm. We could also customize as per the specific conditions.

Working Process of Radiator Separating Machine

1. Cut off the iron ends from the radiator, in case they will damage the blades.
2. Cut the clean radiators to 30-40cm wide with a band saw to fit the width of the material inlet (We also provide the band saw if you need it).
3. To process two-row radiators, remove the roller from the lower cutter shaft to expose the blades.
4. Push radiators into material inlets according to the respective center distance, the left(right) side of radiators must touch the left(right) side of the material inlet, thus each feeding gear will be at the middle of each two copper pipes.
5. For two-row radiators, the first copper pipe in the upper layer shall be nearer to the left side, otherwise, the copper pipes won’t come out. You can also make the right side of the radiators touch the right side of material inlets, then the first copper pipe in the lower layer shall be nearer to the right side.
6. Feeding gears gnaw at radiators and take them into the machine, the blades are right above each copper pipe and gash the aluminum fin, then copper pipes and aluminum fin will come out from the outlet automatically.

Technical Parameters of Radiator Separator Machine

Difference between the C2 and C3 

TKIA-C3 has the main updates in the following aspects.

a. Electric leakage protection
b. Add Two A.C. contactor to protect the motor

Note

1. There is no need to cover the lower blades when you need to process the single layer radiator. It could directly make the adjustment.
2. Before feeding the radiators into the machine, the galvanized iron sheet should be removed. It will break the blades of the machine. You could use an electrical saw or band saw or other ways.
3. When radiators are more than 2 layers or wider than 40 cm, a band saw is needed to split them into one or two layers of suitable width. (We also provide the band saw if you need it)

TKIA-C2 has the main updates in the following aspects.

This machine only can process one layer or two layers radiator with a width of 19mm, 21mm, and 25mm. If it is bigger than two layers or bigger than 25mm, You need to cut the radiators by the band saw.
Usually, we also need the saw machine to sperate the big radiator into small pieces

Motor: 2.2kw
Rotation Speed: 770rpm
Max width: 310mm
Max thickness of the material: 260mm
Diameter: 800mm
Dimension: 900x620x1860
Weight: 180kg